融着接続器
S123C
| Applicable Fibers | SM (ITU-T G.652), MM (ITU-T G.651), DSF (ITU-T G.653), NZD (ITU-T G655), BIF/UBIF (Bend Insensitive Fiber ITU-T G.657) |
|---|---|
| Cladding 直径 | 125 μm |
| Coating 直径 | 250 to 900 μm |
| Fibers Cleave 長さ | 5 to 10 mm or 16 mm |
| Average Splice Loss | SM: 0.05 dB, MM: 0.02 dB, DSF 0.08 dB, NZD 0.08 dB |
| Splice Time | 13 seconds |
| Heat Time | 25 seconds *1 (S922: 40 mm sleeve, S921: 60 mm sleeve) (Pre-heat mode) 31 seconds *6 (S922: 40 mm sleeve, S921: 60 mm sleeve) (Regular mode) |
| Splice Programs | Max. 150 |
| Heat Programs | Max. 18 |
| Automatic Heating Start | Available |
| Applicable Sleeves | 20/40/60 mm |
| Fiber Holding | Tight holder (Loose tube applicable) or Removal fiber holder system |
| Tension Test | 1.96 N |
| Return Loss of Splice | 60 dB or more |
| Fiber Image Magnification | 58X |
| Splice Memory | Max. 1500 |
| Image Capture Capacity | Last 100 images to be automatically captured + Up to 24 images to be stored permanently |
| Dimension | 127W × 199D × 81H mm (not including shock absorber) 159W × 231D × 104H mm (including shock absorber) |
| Weight | 1.4 kg (without battery), 1.6 kg (with battery) |
| Monitor | 3.5” color LCD monitor |
| Data Output | USB ver. 2.0 mini |
| Battery Capacity*7 | Typical 70 splice/heat cycles with S943B battery |
| Wind Protection | Max. wind velocity of 15 m/s. |
| 動作温度 | -10 to 50 ̊C (without excessive humidity) |
| 動作ストレージ温度 | -40 to 60 ̊C (without excessive humidity) |
| Humidity | 0 to 95% RH (non-condensing) |
| 電源 | AC input 100 to 240 V (50/60 Hz), DC Input 11 to 17 V without any change of hardware |
- *6 The first heating after turning on the power can be longer than usual heating time.
- *7 The number of the splicing and heating the machine can produce using a full charged battery at room temperature of 20 ̊C, semi-auto mode for splicing and regular mode for heating. Depending on the condition of the battery and the operation environment, the number can vary.
FITEL NINJA NJ001
| Applicable Fibers | SM (ITU-T G.652), MM (ITU-T G.651), DSF (ITU-T G.653), NZD (ITU-T G655), BIF/UBIF (Bend Insensitive Fiber ITU-T G.657) |
|---|---|
| Cladding 直径 | 125 μm |
| Coating 直径 | 160 to 900 μm |
| Fibers Cleave 長さ | 5 to 10 mm or 16 mm |
| Average Splice Loss | SM: 0.05 dB, MM: 0.02 dB, DSF 0.08 dB, NZD 0.08 dB, BIF/UBIF: 0.05 dB |
| Splice Time | 13 seconds |
| Heat Time | 17 seconds (40 mm sleeve*4)) , 20 seconds (60 mm sleeve*4)) (Pre-heat mode)*5) 31 seconds (S922: 40 mm sleeve, S921: 60 mm sleeve) (Regular mode)*5) |
| Splice Programs | Max. 150 |
| Heat Programs | Max. 30 |
| Automatic Heating Start | Available |
| Applicable Sleeves | 20/40/60 mm |
| Fiber Holder | Tight holder (Loose tube applicable) or Removal fiber holder system |
| Tension Test | 1.96 N |
| Splice Return Loss | 60 dB or more |
| Fiber Image Magnification | 58X |
| Splice Memory | Max. 1500 |
| Image Capture Capacity | Last 100 images to be automatically captured + Up to 24 images to be stored permanently |
| Dimension | 124W × 161D × 64.5H mm (not including rubber pad) 139W × 176D × 71H mm (including rubber pad) |
| Weight | 970 g (with S946 battery) |
| Monitor | 3.5” color LCD monitor |
| Propulsion (motor) | 8 N (Designed value) |
| Data Output | USB ver. 2.0 mini |
| Battery Capacity | Typically 100 splice/heat cycles*6) |
| Wind Protection | Max. wind velocity of 15 m/s. |
| 動作温度 | -10 to 50°C (without excessive humidity) |
| 動作ストレージ温度 | -40 to 60°C (without excessive humidity) |
| Humidity | 0 to 95% RH (non-conden |
| 電源 | AC input 100 to 240 V (50/60 Hz), DC Input 11 to 17 V without any change of hardware |
- *4) The heating time may vary depending on the type of sleeves.
- *5) The first heating cycle after turning the power on can be longer than the standard heating time.
- *6) The number of splicing and heating cycles the machine can perform with a fully charged battery at 20℃ in semi -auto splicing mode and regular heating mode. The number of cycles may vary depending on the battery status and operating conditions.
S153A
| Applicable Fibers | SM (ITU-T G.652), MM (ITU-T G.651), DSF (ITU-T G.653), NZD (ITU-T G.655), BIF/UBIF (Bend insensitive fiber, ITU-T G.657) |
|---|---|
| Cladding 直径 | 80~150 μm |
| Coating 直径 | 100~1,000 μm |
| Fiber Cleave 長さ | 5~16 mm |
| Average Splice Loss | SM: 0.04 dB, MM: 0.02 dB, DSF: 0.06 dB, NZD: 0.06 dB |
| Splice Time | 9 seconds (semi-auto mode) 11 seconds (regular mode) |
| Heat Time | 25 seconds*6 (S922: 40 mm Sleeve, S921: 60 mm Sleeve) (Pre-heat mode) Heat Time 31 seconds*6 (S922: 40 mm Sleeve, S921: 60 mm Sleeve) (regular mode) |
| Splice Programs | Max. 150 |
| Heat Programs | Max. 18 |
| Automatic Heating Start | Available |
| Applicable Sleeves | 20/40/60 mm |
| Fiber Holding | Tight holder (Loose tube applicable) or Removal Fiber Holder System |
| Tension Test | 1.96 N |
| Return Loss of Splice | 60 dB or greater |
| Fiber Image Magnification | 76X, 235X |
| Splice Memory | Max. 2,000 |
| Image Capture Capacity | Last 100 images to be automatically captured + Up to 24 images to be stored permanently |
| Dimension | 127W × 199D × 105H mm (not including shock absorber) 159W × 231D × 130H mm (including shock absorber) |
| Weight | 1.7 kg (without battery) 2.1 kg (with two batteries) |
| Monitor | 3.5” color LCD monitor |
| Data Output | USB ver.2.0 mini |
| Battery Capacity | Typical 80 splice/heat cycles with single battery*7 Typical 200 splice/heat cycles with 2 batteries*8 |
| Altitude | 5,000 mh |
| Wind Protection | Max. wind velocity of 15 m/s. |
| 動作温度 | -10 to +50°C (0 to 95% Relative Humidity [Non-Condensing]) |
| 動作ストレージ温度 | -40 to +60°C (0 to 95% Relative Humidity [Non-Condensing]) |
| Humidity | 0 to +95% RH (non-condensing) |
| 電源 | AC Input 100 to 240 V (50/60 Hz), DC Input 11 to 17 V without any change of hardware |
- *6 The first heating after turning on the power can be longer than the usual heating time.
- *7 The number of the splicing and heating the machine can produce using a fully charged brand new battery at room temperature of 20°C, semi-auto mode for splicing and regular mode for Heating. Depending on the condition of the batteries and operation environment, the number can vary.
- *8 The number of the splicing and heating the machine can produce using 2 fully charged brand new batteries at room temperature of 20°C, semi-auto mode for splicing and regular mode for Heating. Depending on the condition of the batteries and operation environment, the number can vary.
S179A
| Applicable Fibers | SM (ITU-T G.652, G.657A1 and G.657A2), MM (ITU-T G.651), DSF (ITU-T G.653), NZD (ITU-T G.655), BIF/UBIF (Bend Insensitive Fiber ITU-T G.657B3) |
|---|---|
| Cladding 直径 | 80 – 150 μm |
| Coating 直径 | 100 – 3000 μm |
| Fibers Cleave 長さ | 5 – 16 mm |
| Average Splice Loss | SM:0.02dB, MM:0.01dB, DSF:0.04dB, NZD:0.04dB |
| Splice Time | 6 seconds (Semi-auto mode) 9 seconds (Regular mode) |
| Heat Time | 9 (60 mm, Tyco SMOUV1120-1, coating diameter 250-900 μm, Power mode)9 13 (60 mm, FITEL S921, coating diameter 250 μm, Power mode) 15 (60 mm, FITEL S921, coating diameter 900 μm, Power mode) |
| Splice Programs | Max. 300 |
| Automatic Splicing Selection | Available |
| Heat Programs | Max. 100 |
| Automatic Heating Start | Available |
| Applicable Sleeves | 20/40/60 mm |
| Fiber Holding | Tight holder (loose tube applicable) or Removable Fiber Holder System |
| Tension Test | 1.96 N |
| Return Loss of Splice | 60 dB or more |
| Attenuation Splice Function | Intentional high splice loss of 0.1dB to 15dB(0.1dB step) can be made for an inline fixed attenuator |
| Fiber Image Magnification | 278X, 556X |
| Splice Result Strage | 20,000 |
| Image Capture Capacity | Last 100 images to be automatically captured + up to 100 images to be stored permanently |
| Dimension | 138W x 211D x 114H mm (not including shock absorber) 170W x 238D x 122H mm (including shock absorber) |
| Weight | 1.6 kg (without battery), 1.9 kg (with battery) |
| Monitor | 4.3” wide color LCD monitor with touch screen |
| Propulsion (motor) | 8 N (designed value) |
| Data Output | USB ver. 2.0 mini B |
| Battery Capacity*7 | Typical 200 splice/heat cycles, 120sec/cycle Typical 230 splice/heat cycles, 90sec/cycle |
| Altitude | 5000m |
| Wind Protection | 15 m/s |
| 動作温度 | -10 to + 50 °C (without excessive humidity) |
| 動作ストレージ温度 | -40 to +60 °C (without excessive humidity) |
| Humidity | 0 to + 95% RH (non-condensing) |
| 電源 | C Input 100 to 240V (50/60Hz), DC Input 11 to 24 V without any change of hardware |
S123Mシリーズ
| Applicable Fibers | SM (ITU-T G.652), MM (ITU-T G.651), DSF (ITU-T G.653), NZD (ITU-T G.655), BIF/UBIF (Bend Insensitive Fiber ITU-T G.657) |
|
|---|---|---|
| Cladding 直径 | 125 μm | |
| Coating 直径 | Single fiber: 250 to 900 μm, Ribbon fiber: 280 to 400 μm (thickness) | |
| Fibers Cleave 長さ | 10 mm | |
| Average Splice Loss | SM: 0.05 dB, MM: 0.02 dB, DSF 0.08 dB, NZD 0.08 dB | |
| Splice Time | Single fiber: 15 seconds, Ribbon fiber: 15 seconds | |
| Heat Time | Ribbon fiber: 36 seconds*6 (S924: 40 mm sleeve) (Pre-heat mode) | |
| Splice Programs | Max. 150 | |
| Heat Programs | Max. 18 | |
| Automatic Heating Start | Available | |
| Applicable Sleeves | 40/60 mm | |
| Fiber Holding | Fiber holder System | |
| Tension Test | 1.96 N | |
| Return Loss of Splice | 60 dB or more | |
| Fiber Image Magnification | 48X [S123M4], 28X [S123M8], 20X [S123M12] | |
| Splice Memory | Max.1500 [S123M4], Max.1000 [S123M8, S123M12] | |
| Image Capture Capacity | Last 100 images to be automatically captured + Up to 24 images to be stored permanently | |
| Dimension | S123M4 | 127W×199D×81H mm (not including shock absorber) 159W×231D×104H mm (including shock absorber) |
| S123M8, S123M12 | 127W×199D×105H mm (not including shock absorber) 159W×231D×130H mm (including shock absorber) |
|
| Weight | S123M4 | 1.4 kg (without battery), 1.6 kg (with battery) |
| S123M8, S123M12 | 1.6 kg (without battery), 2.0 kg (with two batteries) | |
| Monitor | 3.5” color LCD monitor | |
| Data Output | USB ver. 2.0 mini | |
| Battery Capacity*7 | Typical 70 splice/heat cycles with S943B battery (S123M4) | |
| Typical 160 splice/heat cycles with two S943B batteries (S123M8, S123M12) | ||
| Wind Protection | Max. wind velocity of 15 m/s. | |
| 動作温度 | -10 to 50 ̊C (without excessive humidity) | |
| 動作ストレージ温度 | -40 to 60 ̊C (without excessive humidity) | |
| Humidity | 0 to 95% RH (non-condensing) | |
| 電源 | AC input 100 to 240 V (50/60 Hz), DC Input 11 to 17 V without any change of hardware |
|
- *6 The first heating after turning on the power can be longer than usual heating time.
- *7 The number of the splicing and heating the machine can produce using a full charged battery at room temperature of 20 ̊C, semi-auto mode for splicing and regular mode for heating. Depending on the condition of the battery and the operation environment, the number can vary.
S178LDF
| Applicable Fibers | LDF, SM, MM |
|---|---|
| Cladding 直径 | 125 to 450 μm |
| Coating 直径 | 150 to 2000 μm |
| Fiber Cleave 長さ | 10 mm |
| Average Splice Loss | SM: 0.02dB, MM: 0.01dB (125 μm cladding fiber) |
| Splice Time | 9 seconds (125 μm cladding SM fiber) |
| Heat Time *1) | 31 seconds *1) (S922: 40 mm Sleeve, S921: 60 mm Sleeve) |
| Splice Programs | Max. 150 |
| Heat Programs | Max. 18 |
| Applicable Sleeves | 20 / 40 / 60 mm |
| Splice Memory | Max. 2000 |
| Dimension | 159 W x 231D x 130 H mm (including shock absorber) |
| Weight | 1.9 kg (without battery) |
| Monitor | 3.5” color LCD monitor |
| Data Output | USB ver.2.0 mini |
| Battery Capacity *2) | Typical 60 splice / heat cycles with single battery |
| 動作温度 | – 10 to +50°C (0 to 95% Relative Humidity [Non-Condensing]) |
| 動作ストレージ温度 | – 40 to +60°C (0 to 95% Relative Humidity [Non-Condensing]) |
| Humidity | 0 to 95% Relative Humidity (Non-Condensing) |
| 電源 | AC Input 100 to 240 V (50/60Hz), DC Input 11 to 17 V |
- *1) The first heating after turning on the power can be longer than the usual heating time.
- *2) The number of splicing and heating cycles the machine can produce using a fully charged brand new battery at room temperature of 20oC, semi-auto mode for splicing 125 μm cladding fiber and regular mode for heating. Depending on the condition of the battery and operation environment, the number can vary.
S183PMII/S184PM-SLDF
| Applicable Fibers *1) | SM, MM, DSF, NZD, EDF, PMF, LDF, PCF, HighΔ | SM, MM, DSF, NZD, EDF, PMF, LDF, PCF, HighΔ |
|---|---|---|
| Cladding 直径 | 80 to 500 μm | 80 to 1200 μm *4) |
| Coating 直径 | 160 to 2000 μm | 160 to 2000 μm |
| Fibers Cleave 長さ | 3 to 5 mm with coating clamping 9 to 11 mm with bare fiber clamping |
5 mm with coating clamping 9 to 11 mm with bare fiber clamping |
| Sweep 長さ | ±1.9 mm | ±1.9 mm |
| Typical Insertion Loss *2) (Similar Fiber Splicing) |
0.02 dB for identical SM/0.01 dB for identical MM 0.04 dB for identical DSF/0.05 dB for identical PMF |
0.03 dB for identical SM |
| Typical Insertion Loss *2) (Dissimilar Fiber Splicing) |
0.15 dB (SMF to DSF) 0.25 dB (SMF to HI980 Fiber) |
0.15 dB (SMF to DSF) 0.25 dB (SMF to HI980 Fiber) |
| 消光比 (Cross Talk) *2) (Similar Fiber Splicing) |
-40 dB (0.6 degree) (PANDA Fiber) -32 dB (1.4 degree) (BOW-TIE Fiber) |
-35 dB (1.0 degree) (PANDA Fiber) -30 dB (1.8 degree) (BOW-TIE Fiber) |
| 消光比 (Cross Talk) *2) (Dissimilar Fiber Splicing) |
-30 dB (1.8 degree) (PANDA Fiber to BOW-TIE Fiber) | -28 dB (2.3 degree) (PANDA Fiber to BOW-TIE Fiber) |
| Return Loss | >60 dB | >60 dB |
| Splice Time *3) | 15 seconds for identical SM Fibers 35 seconds for identical PM Fibers (cladding clamping) 55 seconds for identical PM Fibers (coating clamping) |
20 seconds for identical SM Fibers 45 seconds for identical PM Fibers (cladding clamping) |
| Heating Time | 51 seconds for 60 mm sleeves 40 seconds for 40 mm sleeves |
51 seconds for 60 mm sleeves 40 seconds for 40 mm sleeves |
| Manual Splicing Mode | Gap setting Manual alignment (X, Y, θ) Support Tool for Manual splicing |
Gap setting Manual alignment (X, Y, θ) Support Tool for Manual splicing |
| Auto Splicing Mode | SM•MM•DSF automatic recognition Splicing dissimilar fiber PANDA fiber Auto |
SM•MM•DSF automatic recognition Splicing dissimilar fiber PANDA fiber Auto |
| Splice Programs | 72 Default/150 Available | 43 Default/150 Available |
| Heating Programs | 10 Default/12 Available | 10 Default/12 Available |
| Sleeve | 20, 40, 60 mm | 20, 40, 60 mm |
| Magnification | 215X & 430X | 215X & 430X |
| Splice Memory | Maximum 2000 splices | Maximum 2000 splices |
| Size | 350W × 197D × 154H mm | 350W × 197D × 154H mm |
| Weight | 8.5 kg | 8.8 kg |
| Monitor | 6.5” colour LCD monitor | 6.5” colour LCD monitor |
| Video Output | Analog RGB | Analog RGB |
| Data Interface | USB ver.1.1 end Ethernet | USB ver.1.1 end Ethernet |
| 動作温度 | 0 to +40°C (without excessive humidity) | 0 to +40°C (without excessive humidity) |
| 動作ストレージ温度 | -40 to +60°C (without excessive humidity) | -40 to +60°C (without excessive humidity) |
| 電源 | AC 100 to 240 V (50/60 Hz, AC Adaptor) | AC 100 to 240 V (50/60 Hz, AC Adaptor) |
- *1)It applies the fiber specified in the ITU-T standard. Regarding the type of fibers, it is necessary to optimize the splice program.
- *2)These are typical data values. Depending on the fibers, the values can vary.
- *3)Depending on program setting, the time can vary.
- *4)The maximum value of cladding diameter can be 500 μm depending on the type of fiber( PHOTONIC CRYSTAL and non-circle fiber, etc.).
S185EDV-11
| 品名 | 品番 | S185EDV-11 |
|---|---|---|
| 融着接続機本体 | S185EDV-X-A-0001 | 1台 |
| ハードタイプ収納ケース | HCC-12 | 1個 |
| 内蔵バッテリ | S947C | 1個 |
| ACアダプタ | S981A | 1個 |
| AC電源コード | － | 1本 |
| Zロック | ZL-01 | 1組 |
| 予備電極棒 | ELR-03 | 1組 |
| 細径用後側LEDカバー | － | 1組 |
| 電極棒研磨用ゴム砥石 | D5111 | 1個 |
| V溝清掃ブラシ | VGC-01 | 1個 |
| 取扱説明書 | － | 1冊 |